Are you in search of details about Tools You Need to Install a New Bathtub ?
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately challenging project. If the old tub is readily easily accessible, the project can move speedily; if you have to open a wall to eliminate the old tub and position the new bath tub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is far better to consider using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will aid you mount a brand-new bath tub in your restroom if you have currently purchased a new bathtub and also do not need to alter the arrangement of your previous water pipelines.
Your tools and also material checklist must make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will originate from the pipes. Once the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind must be attached to the faucet ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub until the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water supply as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bath tub as well as additionally check the overflow electrical outlet and the typical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has been made use of at the very least once as this will settle it right into its final position.
Getting ready for the Installation
To start with, the supporting framework supplied with the bath should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its final setting.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall between the bathroom as well as the tiling, bring about problems with moisture and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are sold in tubes as well as cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in use. The sealer can crack fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about How to Install a Bathtub? Write feedback below. We would be pleased to know your feelings about this review. We hope that you come back again before long. Enjoyed our write-up? Please share it. Let other people discover it. We take joy in reading our article about How to Install a Bathtub.
Quality service? Ring us.